Little Giant Pumps

Click here for an instant quote and full spec sheet.

• Can handle liquids with 3/4" solids


• Cast iron pump-housing, impeller and volute with protective epoxy coating for rust resistance and corrosion protection.


• Oil filled motor housing - allows for lifetime mechanical seal and bearing lubrication, and extremely efficient heat dissipation.


• Stainless steel components (screws, bolts, handle and seal assembly).


• Mechanical-type seal (stainless steel spring, nitrile parts, carbon and ceramic faces) with secondary exclusion seal.


• High speed (3450 RPM) ball bearing motor with thermal overload protection - allows for high head operation.


• Permanent split capacitor design.


• Capacitor and power cord connections are isolated from oil-filled motor housing (keeps field maintenance easy).


• Dynamically balanced two-vane vortex impeller with pump-out vanes. This keeps solids away from seal and lowers seal and bearing wear.


• 2" Discharge

Click here for an instant quote and full spec sheet.

• 1/2 HP Shaded Pole Motor


• 73 GPM @ 5'


• Intermittent Liquid Temp. up to 120F


• 1 1/2" Discharge


• Cast Iron Housing


• ABS Volute


• Nylon, Glass-filled Impeller


• Carbon/Ceramic Shaft Seal


• 10' Power Cord


• Thermal Overload Protection

Eliminator® Effluent Pumps - 10E-CIM Series

This pump is designed to handle tough, demanding tasks for effluent and wastewater and effluent waste transfer with high efficiency and long term dependability. This pump can be used for residential, commercial, industrial and agricultural applications with light to medium transfer demands. For dewatering, effluent waste, wastewater and handling where such materials must be moved upward from a collection area to sewer or septic lines, or drainage areas, the Eliminators are an ideal solution

Click here for an instant quote and full spec sheet.

• This pump can handle liquids and 3/4" diameter solid waste material


• Constructed of a cast iron pump housing with a protective epoxy coating for corrosion and rust resistance


• Features an oil-filled motor housing. This allows for lifetime lubrication and rapid heat dissipation


• Ball bearings upper and lower to handle radial and axial loads.


• Stainless steel components (screws, bolts, handle and seal assembly)


• Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces)


• Thermal overload protection


• Manual operation


• 1-1/2" Discharge

Eliminator® Effluent Pumps - 10E-CIA-VDS

• 1/2 HP Split Phase Motor


• 80 GPM (303 LPM) @5' (1.52m) Maximum flow rate


• 26' (7.9m) Maximum Head
  # 3/4" (19mm) Solids Handling


• Liquid temp. to 140F (60C)


• 1 1/2" (38.1mm) FNPT Discharge


• Epoxy coated cast iron housing


• Glass-filled nylon Relay Cover


• ABS/Cast iron Volute


• Vortex nylon Impeller


• Carbon/Ceramic Shaft Seals


• Upper and lower ball bearings


• Vertical Diaphragm Switch with Piggyback plug

Click here for an instant quote and full spec sheet.

Eliminator® Effluent Pumps - 10E-CIM

• Cast iron pump housing with protective epoxy coating for corrosion and rust resistance


• Oil filled motor housing for lifetime lubrication and rapid heat dissipation


• Ball bearings upper and lower to handle radial and axial loads


• Stainless steel screws, bolts, handle and seal assembly


• Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces)


• Thermal overload protection


• Manual operation


• 1-1/2" Discharge

Click here for an instant quote and full spec sheet.

Eliminator® Effluent Pumps - 10E-CIA-SFS

• Handle liquids and 3/4" diameter solid waste materials.


• Cast iron pump housings with epoxy coating for corrosion and rust resistance.


• Oil-filled motor housings for life-time lubrication and rapid heat dissipation


• Stainless steel screws, bolts handle and seal assembly


• Mechanical seals (stainless steel spring, nitrile parts carbon and ceramic faces)


• Thermal over protection


• Automatic operation has approximately 8" - 11" "On" range and 2" - 5" "Off" range with integral snap-action float switch


• PSC type motor with upper and lower ball bearings


• 1-1/2" Discharge

Click here for an instant quote and full spec sheet.

Eliminator® Effluent Pumps - 10E-CIA-RFS Series

• Handle liquids and 3/4" diameter solid waste materials.


• Cast iron pump housing with protective epoxy coating for corrosion and rust resistance.


• Oil filled motor housing for lifetime lubrication and rapid heat dissipation


• Ball bearings upper and lower to handle radial and axial loads.


• Stainless steel screws, bolts, handle and seal assembly


• Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces).


• Thermal overload protection.


• Manual operation


• Automatic operation has a 11" - 15" "On" level and, and 5" - 9" "Off" level range with adjustable Remote Float Switch.


• 1-1/2" Discharge

Click here for an instant quote and full spec sheet.

This pump is part of the Big John Submersible Sump Pumps series. Designed for continuous or extended use in moving large volumes of water, they are efficient and trouble-free. These Little Giant pumps are available in manual or automatic versions. Little Giant's submersible sump pumps are perfect for use in Excavation, Crawl Space, Basement, Underground Passageway, Loading Docks, Grain Elevator, Construction Site, Cooling Tower, Fire Cleanup and any applications requiring large volume water dispersal.

Click here for an instant quote and full spec sheet.

• Epoxy coated cast iron pump housing


• 1/2 HP Split Phase Motor


• Stainless steel screws, bolts, and handle


• Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces)


• Nylon switch housing


• Thermal overload protection


• Manual and automatic models


• Automatic operation with pressure switch operates when water level is between 8-1/2" to 12". Pump shuts off when water level falls to between 1-1/2" - 5" (Pressure switch is non-adjustable)

Big John Submersible Sump Pumps - 10-CIA

• Cast iron pump housing with protective epoxy coating for corrosion and rust resistance.


• Oil filled motor housing for lifetime lubrication and rapid heat dissipation


• Stainless steel screws, bolts, and handle.


• Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces).


• Nylon switch housing.


• Thermal overload protection.


• Automatic models.


• Automatic operation with pressure switch operates when water level is between 8-1/2" to 12". Pump shuts off when water level falls to between 1-1/2" - 5" (Pressure switch is non-adjustable).


• 1-1/2" Discharge

Click here for an instant quote and full spec sheet.

Big John Submersible Sump Pumps - 12-CBM

• Cast bronze pump housing for corrosion and rust resistance


• Oil filled motor housing for lifetime lubrication and rapid heat dissipation


• Stainless steel screws, bolts, and handle


• Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces)


• Nylon switch housing


• Thermal overload protection


• Manual operation


• 1-1/2" Discharge

Click here for an instant quote and full spec sheet.

Big John Submersible Sump Pumps - 12-CBA

• Cast bronze pump housings for corrosion and rust resistance.


• Oil filled motor housing for lifetime lubrication and rapid heat dissipation


• Stainless steel screws, bolts, and handle.


• Mechanical seals (stainless steel spring, nitrile parts, carbon and ceramic faces).


• Nylon switch housing.


• Thermal overload protection.


• Automatic operation


• Automatic operation with pressure switch operates when water level is between 8-1/2" to 12". Pump shuts off when water level falls to between 1-1/2" - 5" (Pressure switch is non-adjustable).

Click here for an instant quote and full spec sheet.