Dyeing Yarn with KoolAid

The beauty of dyeing at home is that you can work with what you have!

WOOL: You need some kind of fiber. For dyeing with kitchen items, only 100% wool will take the dye. You can, however, use blends, as you will see in the links I have been able to dye Lion Brand Wool-Ease which is only 20% wool with food coloring. You will not be able to get 100% acrylic to hold with these methods.

DYE: Kool Aid and/or Food coloring (either paste that you dissolve in water or liquid in a dropper, I've used both). You want to make sure that any Kool Aid you use is sugar free! (I wouldn't want ants to try to eat my sweater!)

ACID: You need mildly acidic conditions to get the dye to take to the yarn. The acid source can be the citric acid in Kool Aid pouches, or it can be common white vinegar. Sometimes you may end up using both, as the amount of acid can mildly affect the tone of your color.

HEAT: The second thing you need to set the color to your wool is heat. I tend to use the microwave for handpainted colorways, and the stove top for dip-dyeing and single color batches.

CONTAINER: As you may have gathered from the heat section, you will need to have something to put the wool in when you are heating it. This can be a plate with seran wrap over it for the microwave, or a pot.

SAFETY: The only real personal danger here is burns. BUT the less dangerous danger is coloring yourself. I recommend using latex gloves just to keep your hands their flesh color. Use oven mitts when touching hot pots or plates coming out of the microwave. I will cover my work area with plastic bags or seran wrap so my art project doesn't leave stains on the work surface.

As described on my blog at www.chemknits.com

I started with experimenting with Lion Brand Wool Ease yarn, and I wanted to try to make a rainbow handpainted colorway. To remind you, Wool Ease is only 20% wool, but as you will see that is enough for your kitchen dyeing to take hold. I loosely followed the protocol from Pea Soup, but I did not use nearly as much food coloring as they did.

ACID: KoolAid served as the basis for the acid in this project, no additional acid (vinegar) was used. (This is going to smell so yummy!)

THE YARN: 1 ball of Wool Ease was wound into a skein, and then soaked in room temperature water until it was completely saturated (a couple of hours should be sufficient. Make sure you check the inside of the skein, or you could end up with white patches like in a tie-dyed shirt)

THE TOOLS: A garbage bag over the work station (my kitchen table) a 10 mL syringe that I had from lab, but you don't really need anything to apply, you can just pour, small glasses (shot glasses will do), a microwave safe plate and seran wrap. Don't forget to protect your hands or they may change color too!

SETTING UP THE DYES: Red (2 packets Cherry Kool-Aid), Blue (2 packets Ice Blue Raspberry Lemonade) and yellow (1 packet lemonade). Each were dissolved in 1/4 cup water. With a 10 mL syringe that I took from lab, I transferred 10-12 mL of each primary color into three smaller glasses. (9 glasses total) I then would use some McCormick food coloring, standard and NEON! varieties, to create my rainbow.

I then mixed the colors as follows (where 1 refers to the Big cup):

• Blue 1 - 10 drops of NEON blue
• Blue 2 - 5 drops NEON purple
• Blue 3 - 8 drops NEON pink, 5 drops NEON blue
• Blue 4 - 5 drops green
  
• Yellow 1 - 10 drops yellow
• Yellow 2 - 5 drops NEON green
• Yellow 3 - 2 drops yellow, 2 drops NEON green, 2 drops green
• Yellow 4 - 3 drops yellow, 5 drops red
• Red 1 - 10 drops red
• Red 2 - 4 drops blue
  
• Red 3 - 5 drops yellow
• Red 4 - 6 drops NEON blue

Now looking at the liquid you cannot get a real sense of the colors. I dipped a fork into each dye sample, and made a mark on a paper towel to see how the colors came out.

The order to bring the best rainbow: R1, R2, R4, B2, B3, B1, B4, Y3, Y2, Y1, Y4, R3

APPLYING THE DYE: As I mentioned previously, I covered my kitchen table with trash bags and then covered them with paper towels to absorb any dye spills. I placed some seran wrap on the work space, and then put the skein in the center.

I applied the dye to the skein in sections (think about making a tie dyed T-shirt). You want to make sure you work the dye through the entire section by lightly pressing with my fingers, so that it reaches the middle of that portion of the skein. Of course, part of the beauty of hand painted yarn is that the repeats are not identical, so play around with this. After I applied all of my colors to the skein, I went through and with my fingers pushed the die so there would be some blending at color junctions, and so there would be no white spaces.

APPLYING THE HEAT TO SET THE COLOR: In this next step you want to try to keep parts of the skein separate so there isn't bleeding of the colors. Wrap up the skein with plastic wrap as best as you can, place it on a microwave safe plate and cover the plate with more plastic wrap. Microwave on high for 5 min (or until you hear it boiling) and then allow the plate and yarn to cool until you can touch it comfortably. Repeat this process. Make sure that the yarn is still wet during this whole process, if needed add some more (clear) water.

REMOVE THE EXCESS DYE: Allow the yarn to cool completely. Rinse the skein in luke warm water until the water runs clear. Use some mild soap (dish soap is fine) and rinse the skein thoroughly. You may have a lot of dye to rinse out, or only a little. Hang the yarn to dry.

The colors have dimmed a bit, but remember that I was working with 80% acrylic, 20% wool yarn. If you were working with 100% wool the colors would be VIBRANT.

Look how pretty the final ball looks!

This lens earned a purple star on 12/08/2010!