Gold Leaf paint gilding

Liquid Leaf is a gilding paint that contains its own red primmer and a film of lustrous gold, pre-mixed into a single liquid.
An effective finish for use on carved and ornamental furniture, frames, mouldings, decorative ceilings, lamps, figurines and objects.
Flows easily onto the surface with no brush marks, forming a beautiful lustrous finish that resembles traditional gold leaf.
It is so controllable, it can be used with a striping brush or ruling pen for fine lines and scrolls.
When dry can be buffed with a soft cloth or toned down with a used shoe polish brush

Non tarnishing wax gilt is ideal for restoring gold leaf and decorating almost any surface. Classic, Florentine, Renaissance, white fire, brass, copper, pewter, silver, Aquamarine , Royal Amethyst, Olive Bronze , Emerald Green, Sapphire, Rose Quartz, Onyxite, Ruby, Green amber, Indigo, Spanish Topaz , Yellow Diamond

specifically made as a protective coating for liquid leaf, treasure gold and jewels. It is waterproof, clear and non-yellowing and also provides an excellent exterior hard varnish.
Can be used on fabric, prints, ceramics (non-fired), plastic, leather furniture, wallpaper and straw.
Can also be used to prevent gold paint from tarnishing. Drying time 30 minutes.
Liquid Leaf is a gilding paint that contains its own red primmer and a film of lustrous gold, pre-mixed into a single liquid.
An effective finish for use on carved and ornamental furniture, frames, mouldings, decorative ceilings, lamps, figurines and objects.
Flows easily onto the surface with no brush marks, forming a beautiful lustrous finish that resembles traditional gold leaf.
It is so controllable, it can be used with a striping brush or ruling pen for fine lines and scrolls.
When dry can be buffed with a soft cloth or toned down with a used shoe polish brush

PREPARATION (n.b. the gold will repeat the texture of the prepared surface.)
RAW WOOD - Sand smooth, apply a coat of sealer, sand once more lightly. For a smooth finish gesso can be applied to the sanded wood, sand between coats with a very fine grade sandpaper.

GLASS & VINYL - Make sure surfaces are free of dust, grit and oil based residue. Wipe over with methylated spirits.

PLASTER & TERRA-COTTA - Seal with two coats of sealer after thoroughly cleaning with either detergent and water or meths.

PREVIOUSLY PAINTED OR VARNISHED OBJECTS - A general clean and light sanding will suffice unless the paint is thick, uneven, or chipped. In this case the piece should be thoroughly stripped, then sealed.

2) BASECOATING

After preparing the surface apply one or two coats of bole, ( traditionally used to create the eggshell paint applied beneath the gilded surface), or for modern gilding acrylic paint acts as a satisfactory basecoat.

Dilute the acrylic paint slightly with a matt medium so that the finish is less shiny, and ready to receive the size and leaf that will be applied .

3) APPLYING SIZE

Size is either a water or oil based adhesive used as a mordant to attach metal leaf to a surface. A water based size dries quickly and has a usable tack life. An example of a water based size is
Gedeo Gilding Paste, Eberhard by Staedtler or alternatively an acrylic medium or a good PVA glue thinned to a milky consistency can be used.

A traditional oil based size such as Japan Gold Size works best on hard smooth surfaces but will take longer to dry sufficiently to accept the leaf.

Apply size over the bole/ acrylic painted base coat in smooth even strokes, avoiding puddles and runs, (as the leaf is wafer thin any marks underneath will be visible when finished). As the size dries it will become clear with a tacky consistency. To test if the size is ready to accept the leaf lightly press your knuckle to the surface, if it clicks when you pull it away it is ready. Do not test using your finger tip as it will leave a print that will show through the leaf, or will remove the size from that area. Size will remain tacky for some time, though if leaving overnight make sure the surface is covered and dust free.

4) APPLYING LEAF - the tricky bit - Gold coloured leaf is available in genuine gold and imitation leaf, the genuine leaf will be richer in colour and finish, different coloured metal leaves are also available. Leaf also comes loose or as transfer, (attached to tissue paper), making it easier to apply. Loose leaf requires special tools and skills therefore we advise that you start with transfer. Wear cotton gloves when handling to avoid tarnishing when working with silver or imitation gold, or rub talcum powder on your hands.

Once the size is tacky place the gold leaf on the object and brush it gently with a very soft brush. Lay the next sheet of leaf down so that it overlaps slightly, and repeat until the surface is covered. When applying to raised surfaces you may need to use small pieces of leaf to fill crevices first, and use a soft bristle brush to tamp the leaf into the grooves. To get a shiny metal finish use a burnisher - a pen like tool with a smooth agate stone as a point.
Burnishing Pencil Information Hints and Tips

Brush Cleaning : white spirit can be used to clean brushes , Xylene is a stronger dilutant