How To Build an Easy N Scale Train Layout Including Scenery!

So...I finally tired of setting up my N scale track loop on the kitchen table every year. I would run the train a few times for my daughter and her friends, but not being nailed down, the track would eventually start to separate at the connectors. After a few push-it-back-together track repairs I'd become frustrated and tear it down until the next Christmas....but no more! I decided to make a permanent setup that could be stored against the wall and simply be picked back up whenever I felt like working on it (or my daughter felt like I should run it, lol). Or maybe even be left up all the time.

You can imitate my layout if you like but note that this is my first ever attempt at building an N gauge layout and there's no master plan. I'm pretty much making decisions on the fly, often inventing ways to make what I need as the build progresses. I'll tell you the basics of the endeavor here and you can run with it, come up with your own ideas or implement your own variations on mine.

First you'll need a base: wood of some sort to build the layout on. I went to Lowe's intending to buy a sheet of 3/4" plywood and ended up purchasing a solid door slab for $25, the kind of interior door you'd normally hang between two rooms. They come unpainted and have no knobs, no indented window panels or anything, just a flat slab about 7 foot x 35 inches wide- a perfect layout size. I decided against plywood because good quality plywood is more expensive and far more flimsy than a door slab. I didn't want to build a layout, pick it up and watch everything shift around when the plywood bends. I highly recommend you start with a door slab. It's far cheaper, better and easier than framing a piece of plywood with 2 x 4's.

If space is a problem simply cut the door down to a smaller size.

You could build legs for the door slab from 2 x 4's or set it on the floor and work laying down or possibly even hinge it to the wall. Hinging will make access to that side difficult though! I set my door slab on the good old kitchen table to get started.

So let's lay some track! Here is a list of the tools you'll need and a few optional ones:

Necessary:

A small box of tiny wire nails 1/2" x 19 to nail down the track
A roll of thin, black slightly spongy material to put under the track. I use non-slip shelf liner. Felt would probably work.

Tack hammer
Nail Punch
Nail puller or Flathead Screwdriver
Needlenose Pliers
Small Regular Pliers or Vise Grips
Scissors

No doubt, some serious N scalers will laugh to the high heavens when they read this but this method will achieve our modest goals perfectly and save $ over commercially available roadbed. We'll "ballast the track" later:

1) Figure out where you want your track then remove the track connector on your first piece temporarly, set the track on your felt, shelf liner or whatever medium you've chosen. Pick up both the track and liner and cut out a piece of liner as snug to the perimeter of the track as possible. 2) Put your track connectors back on the rails. Lay the liner with the track on top. Holding a nail with the vise grips carefully tack down one end of the track. Most track has a slightly oversized space between the ties at each end. Place the nail in that space, tight up against the track so the nail head wil push down on the tie. Put one nail at each end. If you're doing a loop design lay it out before you tack it down or it may not line up to close the loop. An optional touch of black magic marker on each nail head will make them about disappear.

Repeat until you have your track laid or at least enough to start on scenery.

I decided to simply make a big loop around the outside of the door, then do a turnout about midway around the outer loop and send a strip of track down under the elevated portion, at the bridge. Your'e looking at about half the track plan here

To the left is the darker, finished area and the remainder of the loop. To the right is a town in the planning stages. I'm considering adding a second door base for this stage.

Notice the roads are wider but made of the same modeling clay used on the country roads. It will just need to be sanded much smoother and have yellow and white lines installed.

Simply put another nail in beside the bad one, or pry it up with a screwdriver or nail puller. Once you pry the nail head up slightly, vise grips or pliers will quickly finish pulling it up.

Be sure to visit this lens also as it has some good photos and details how to build a tunnel, a cornfield, a McDonald's that some have mistaken for the real thing and more!:

http://www.squidoo.com/how-to-make-n-scale-scenery-grass-trees-and-more

80 feet in real size = 6 inches in N Scale

50 feet - 3.75 inches

20 feet= 1.5 inches

10 feet= .75 of an inch

6 feet = .45 inches

3 feet = .225 of an inch

2 feet - .15 inches

1 foot= .075 of an inch

There are excellent, highly detailed N Scale buildings commercially available, but you'll pay $20-$40 for a kit, $40- $150 for a fully assembled structure and even at that price, many fall short of being convincing. This residential house typical of one you'd find on a higher end residential street cost under 50 cents for materials yet looks more realistic than the majority of commercially available houses that look like the cheap plastic they are.

Buldings, cars, people, road signs, light poles....just about everything you see in real life can be duplicated in N Scale!

Let's lay some grass and dirt...and maybe a few trees too. You'll need:

A Bag of Brown Dirt

A Bag of Green Grass

Trees

Elmer's Wood Glue

Nice to have but optional:

Hot Glue Gun instead of the Elmer's

Basically spread the wood glue where you want dirt or grass, then quickly sprinkle the material thinly on the glue. Allow to dry thoroughly.

Most land is not perfectly flat. A gob of hot glue or a longer thinner strip of hot glue, once dry, will provide a slightly raised area to add realism.

Wood glue can do the same type of terrain building but it requires hours to dry instead of the seconds hot glue takes.

To plant trees you can apply the glue to the base of the tree, plant it, then you'll need to hold it in place until it dires. Hot glue dries in less than one minute. Wood glue will take hours so you'll want to position something to hold the tree in place during dry time.

Grass and dirt are both available at N scale dealers but it's expensive and you don't get much at all for the money. You can make your own with sifted sawdust and fabric dye but note that it's difficult to get the color to blend properly and it's a messy, somewhat dirty job, definitely wear gloves and a mask. Obviously use green dye for grass and brown for dirt. It's not a bad idea to mix up a little yellow also.

Some places you'll want pure green, some areas will need pure dirt, but often you'll hsve transitional areas where blends of green, brown, and sometimes yellow, will be more realistic.

If you don't have access to sawdust or don't want to deal with the mess, I'll be happy to make up a 1/2 lb. bag for a reasonable price and ship it to you (see the sales lens below).

When I discovered that commercially available N Scale trees were over $2 each I decided to find an alternative. Some pines are here and I also make leafy maples and oaks. Ditto shrubs and autumn trees sporting red, gold and other fall colors.

I'm biased I guess but I think my homemade trees look far more realistic than the commercially available ones that look like plastic covered wires gloriously adorned with green carpet padding pieces representing leaves.

What do you think?

Gravel can be sifted into different sizes for use as parking lots, boulders, etc. These items, especially the trees, will make a huge difference in how realistic your layout looks.

It may be difficult to see in a pic but the dark green strips around the window and such are not paint, they're little strips of wood which impart an effective three dimensional effect.

This building runs about $40 to $50 if you buy it a train shop. I don't think there's more than fifty cents worth of materials in this do-it-yourself one.

Making your own N scale people, vehicles and animals is a challenge and then some. A 6 foot tall person scales down to less than 1/2 inch so painting them requires extremely fine detail and it's very easy to accidentally break off the model's appendages. They won't cry but seeing an hour of work go down the drain in a snap, you might. Notice the little dude in the camping scene pic at the bottom of this lens, he's about 3/8 inch tall.

The Wal-Mart semi truck in this pic was made using a door magnet for the trailer and modeling clay for the cab & wheels.

I'm using a product called "air dry modeling clay" which is sold at Hobby Lobby. There's a brand called "Cloud" that is perfect but they were out so I purchased Fimo Light- so far, so good. A small $5 block will make a lot of people, vehicles and animals. If you find you can't do it I'll make you some, see below.

A big mistake some modelers make is to draw roads flat on the wood base and paint them. Or they get flat gray plastic roads and glue them down. Not cool at all in my opinion because they look so unrealistic as to be ridiculous and toylike. Look at roads you travel. Typically they're humped toward the middle so water will drain and they usually have a lot of imperfections, especially rural roads.

A better method is to spread some air dry modeling clay very thin, humping slightly toward the middle. Roadways have slight dips and elevations so making the road a bit higher in spots is not a bad idea. Sanding is necessary. In general, city and town roads need to be smoother and rural roads can be pretty lumpy. The pic shows me painting a rural road made of the clay, just up from the depot. To the left is an elevated area made of the clay with a few boulders on it. Later I'll add paint, dirt, grass and such to complete this area.

Notice the phone poles made of thin wood dowels and toothpicks!

This one has a "transformer"- a .22 ratshot shell casing!

Using wood dowells for the vertical pole and square toothpicks for the horizontal poles, I make about three regular poles to each one that has a transformer. String black thread for wires!

I thought it would add beacoup interest to raise the track about 4 to 5 inches at the far end of the large loop. Seeing pre-cut track risers for $150 forced a trip to Home Depot for a discounted 2 x 4 for $1.50 which was then sawed to create the necessary shapes. There's one riser about 2 feet long, the rest is small blocks of various heights. The procedure was to add track, nail it down, then set in the next piece, cutting to order as things proceeded.

Some thin shims (paint stirs are perfect) were added as needed to support the track by filling any gaps and everything was wood glued and hot glued to the door base to make it very stable.

A gap was left about the middle of the short end door base, to allow for a train bridge.

Later, all this wood will be covered with "hillsides" made of paper mache (flour, water and newspaper). Visit my other N Scale lens at http://www.squidoo.com/how-to-make-n-scale-scenery-grass-trees-and-more to see how amazingly good the hills turned out.

Simply send the appropriate amount for the item you want and shipping via Pay Pal to cindyadams2010@yahoo.com. Cindy will ship your order and confirm within 24 hours to the shipping address you enter on your Pay Pal form.

$15 each item plus $5.30 to ship each choice separately in a Priority Mail box to anywhere in the U.S. The box will be filled to the brim with what you need!

• Grass
  
  
• Dirt
  
  
• Buildings Set
  
  
• Trees & Shrubs: Green Leafy, Bare Winter, Brown Leaf Fall
  
  
• Boulders
  
  
• Gravel (assorted boulders, down to driveway sizes)
  
  
• Telephone Poles (with and without transformers)

The Pine Tree Scenery kit (pictured) is an excellent value for $19.50 plus the $5.35 Priority Mail Flat Rate shipping box you receive:

1 bag simulated grass

1 bag simulated dirt

6 boulders

9 pieces of deadfall

20 1-2" pine trees

20 yellow grass tufts

It's late fall and this little guy needs to stay warm!

Sorry, I'm out of room here but if you liked this please take a look at my other lens on this subject:

http://www.squidoo.com/how-to-make-n-scale-scenery-grass-trees-and-more

It has tips on making buildings cheaply that look better than kits sold commercially, how to make a tunnel, how to light your layout for fifty cents per light pole instead of $20 per pole, and more!