Spot Light On Magnetic Electric Generator

Here is a picture of a 3½ volt, 7 amperage magnetic electric generator (24 watts). It must be charged up by driving the main shaft at 2100 RPM for 42 seconds.

This charging process manifests as magnetic energy within the six coils of copper wire, the copper tube supporting these coils and the copper coated steel wires wrapped around the magnets in the magnetic electric generator device.

This charging is accomplished while the six coil connection wires are making contact and setting up their alternating magnetic poles.
After the 42 second charging time one of these coil connection wires must be opened and this circuit again completed through an energy draw at what could be called 7 amps.

This draw sets up magnetic poles, which are a response between the rotor magnets and the coils. This response then causes the main shaft to be rotated by the 12 permanent magnets as they attract and build a release field. Then the driver unit (hand crank) is disconnected, allowing the unit to rotate with the load being the activating driving force.

The fields of the magnets must be maintained during their spin movement. These magnetic fields which are encapsulated are achieved by the wiring system.

Here is a full description about magnetic electric generator device - Mini Romag. The attract-release of the magnets is a function of several factors:

The magnets attract field between north and south is completed by taking a crossing path of attract (top of one row to bottom of next, etc.). This action has the effect of fields blending into fields, and a hold-back attract does not happen.

Each time a magnet set passes a coil an interchange of like energy between the coils around the magnets and the generating coils sets-up neutral polarities which are 'release fields' and prevents a hold-back attract.

One important magnetic assembly is the circuitry which allows this interchange of energy. This is a recycling of a stabilized magnetic/electro energy because the field of force is not a case of electrical input, an input that created the magnetic energy, but rather a build-up of magnetic energy which caused an energy thrust.

In further defining the workings of this unit it is important to understand that although electrical and magnetic (energy) work with similar attitudes, the manner in which they work sets-up a differing energy effect.

One of these effects is that magnetic structures want to share their flow, compatible to the Universal Force, while electrical flow argues (short circuits, sparks, etc.).
Because of this fact the working responses (within the unit) take place, how they are needed, and when they are needed which results in a functioning unit.

There is a continuous transmutation process taking place whereby magnetic energy continually generates an energy that manifests a measurable current.

Read more about Mini Romag magnetic electric generator .

Here is a summarize description about magnetic electric generator device - LEA..

In order to understand the operation of a LEA (Lutec Electricity Amplifier) it must be understood that there are actually three separate individual events occurring in one machine. Each of the three is equally important because without one of them operating in a completely synchronistic manner with the others, the result would not achieve the efficiency levels required.

1. A Pulsed DC Motor.

A DC input current either from a battery bank or from rectified AC mains is supplied to a DC motor comprised.

The input is pulsed by a rotating switch allowing the DC input current to flow through the motor coils for a percentage of one cycle.

The DC pulse causes a magnetic effect in the coil core so that the temporary polarization of the coils laminated steel core has the effect of repulsing the magnetically aligned permanent magnet embedded in the rotor so causing it to rotate.

The DC pulse is completely consumed by this action, which is the cause of the rotor spinning. The result of the consumed DC input pulse is that it initiates the motor moment.

2. An AC Generator.

The same coils are used to generate the Second Event that being an AC power output. The rotor containing the permanent magnets is caused to be driven past the stator coils, at which time induction occurs in the coils that produce an alternating current (AC) output.

The only force being used to cause the movement of the rotor is the motor torque. The AC generated in the coils is done so independent of the input DC pulse and is strictly the result of the induction effect.

3. The Effect of Event Two on Event One.

Events One and Two happen independently of each other in the same machine. They only share the same coil to enable each to perform their independent functions.

The pulsed DC input to the coil has no effect on the AC being produced because there is no return path for it through the AC load of the coil. The DC input runs the motor supplying current through its own defined circuit for around 0.2 of a cycle. (The ON a period)

The AC is being generated continuously, and has no direct electrical contribution to the input because it too has no return path to enable it to do so.

Read more details about LEA magnetic electric generator .

How does the system now when to drive DC input current?
The DC current is driven into the motor coils as long as there is a potential difference in voltage between the DC voltage and the AC voltage. This potential voltage is what carries the input current.

When does the DC input starts?
As long there is a potential difference in voltage between the DC voltage and the AC voltage is what carries the input current will carry on.

When does the DC input stops?
When this potential voltage difference falls to zero the ON period of the electrical cycle is ended, and then the input current cannot flow.

The patent over this magnetic electric generator technology already granted in many countries including the USA, Australia, New Zealand, Canada, Mexico, Russia, Eurasia, Africa, Poland, China, South Africa, Vietnam, Brazil, Singapore, Turkey, Israel and pending in many others is titled;

"A Means of Controlling A Rotary Device"

The reader may now understand why the magnetic electric generator has been called so.

There are many uses for the technology; it can provide electricity in a manner more highly efficient, environmentally clean and cost effective than any other currently known.

Other applications for this technology could be water desalination, hydrogen production, highly efficient motors for plant, pumps, and machinery, or more cost effective drive for anything that turns, spins or rotates.